|
1. |
|
New 124' Inland Steel Steel Barge For Sale
|
|
Custom Modified 2024
|
Inland Spud Barge
|
124'
|
|
|
Custom built, finished in 2024 and USCG Registered. Ready to go.
|
2. |
|
50' Self Propelled Spud Barge On Order
|
|
2024 - Appx 8 Weeks to Completion
|
2024 Self Propelled Spud Barge
|
50'
|
|
|
50x12x4 Raked Bow Barge with following features: 1/4" Plate, 3x3x1/4" framing on 24" centers, 6 cleats, Flush manway, 2 coat epoxy paint system on exterior Internal spudwell 8" 6" sch80 steel spuds 20ft long with hats and pins Antifouling on underwater hull including 3rd coat of epoxy Bolt on plate anodes Aluminum console, dual engine brackets, rigging pipe chase 18" Structural crane pedestal and 6" elevated HPU platform Tiger 1069 Crane- 11,000lb max cap and 29ft max reach BravePro powerpack with 20 HP Honda Engine (2)Yamaha 115 XL shaft with all rigging and install (hydro steering, stainless props, batteries, controls, cables, harness, gauges, etc) Spud ring lifting collars
|
3. |
|
Self Propelled 32' Push Boat Barge on Order
|
|
2024
|
Self Propelled Supd Barge
|
32'
|
|
|
All steel material wheelabrated and preprimed with inorganic zinc incl incl Transverse water-tight bulkhead (1) Deck winch pads on bow 2 incl Deck cleats 6 incl incl 4 internal spudwells 8" diameter and 2 spuds 6" by 20ft long 1 incl 100 gal fuel tank 1 incl incl 2 watertight flush manway hatches 2 incl incl 3 coat paint system with antifouling and bolt on anodes Engine crash guard (removable) 1 incl incl Tiger 7543 crane with wireless remote, 7500lb cap and 30ft reach Hydraulic power unit Honda GX series gas engine 1 included Yamaha 200 XL Shaft engines with hydro strg, batteries, all rigging, etc 2 incl incl Hydraulic wteering system with wet tie-bar connection 1 incl incl
|
4. |
|
40'x10'x4' Raked Bow Steel Barge
|
|
2024
|
Steel Sectional Barge
|
40'
|
|
|
40'x10'x4' Raked Bow Steel Barge: Standard features: 1/4" plate, 4 low profile cleats, 2 flush water-tight manways, transverse water-tight bulkhead, 3x3x1/4" angle framing on 20" spacing, impact protection outside angle cap on leading edge of headlog and rake as well as verticles on transom, 6" gussets on all 4 corners of each frame, 2 spudwells 8" diameter, 6x4x1/2" connecting rails, 1.25" conn pins Exterior epoxy paint system Accessory brackets on transomTerms: 50% down, balance on completion. Lead time- approx 4 weeks...subject to change!
|
5. |
|
NEW 40' x 14' x 4' Self Propelled Spud Barges On Order
|
Custom Build
|
2024
|
Self Propelled Spud Barge
|
40'
|
|
|
These 40x14x4 Raked Bow Sectional Barges include the following features: 5/16" plate, 3x3x1/4 framing on 20" spacing, 6 cleats, flush manways, 4x6 angle connecting rails with 1.25" pins, 2 coat Safety Red anticorrosive exterior epoxy paint and antifouling on the underwater hull. (2) 12" spudwells for 10" spuds, all 30ft long with hats and pins included.
|
6. |
|
New 40'x12'x 4' Construction Barge for Sale- On Order
|
|
2023 Model
|
Spud Barge
|
40'
|
|
|
Just like new. This spud barge was recently built for owner that was too big for their project. Now must sell.
|
7. |
|
New 60' x 20' x 5' Spud Barge #219
|
|
2023
|
Spud Barge
|
60'
|
|
|
60' x 20' x 5' & 7' Dimensional selections Main Deck Plating = 3/8" Side Shell Plating = 5/16" Bottom Shell & Rake Bottom Plating = 5/16" Transom Plating = 5/16" 4x3x1/4” Angle Stiffeners on Hull Plates 3x2x1/4” Angle Stiffeners on Bulkheads Channel 10” Transverse Buck Frames as required Two 1/4” plate transverse watertight bulkheads Two 1/4" plate longitudinal bulkheads Six (6) dry void compartments (not for ballast) Radius corners for bilge and deck knuckles. 2 coats AF paint system for UW hull. Freeboard and rake are painted inorganic primer with two coats of navy blue. Deck is in organic primer with two..
|
8. |
|
Heavy Duty 40'x12'x4' Sectional Barge on Order
|
|
2022
|
Sectional Barge
|
40'
|
|
|
Barge Details – 1 - 11’8”x 40’x 4’ deep Sectional Barges are raked 38 degrees one end with 12” channel head log Three (3) compartments each section three (3) flush mounted watertight hatches Four (4) 18” welded kevels placement per customer specs
|
9. |
|
40'x 11x 4' Medium Duty, Raked Truckable Barge on Order
|
|
2022
|
Heavy Duty Raked Barge
|
40'
|
|
|
Barge Details – 1 - 11’8”x 40’x 4’ deep Sectional Barges are raked 38 degrees one end with 12” channel head log Three (3) compartments each section three (3) flush mounted watertight hatches Four (4) 18” welded kevels placement per customer specs A36 3/16” plate throughout except for deck A36 ¼” plate. All seams welded inside and out below the deck plate Two (2) bulkheads welded in barge,3/16” plate. Transverse frames on 24” centers: 3”x3”x3/16” angle Longitudinal angles under deck 3”x3”x3/16” on 18” centers Sections sand blasted on outside to commercial grade, one coat zinc rich epoxy for added corrosion protection Deck co..
|
10. |
|
40' x 20' x 5' Hydraulic Spud Barge On Order
|
Custom Build
|
2022
|
Hydraulic Spud Barge
|
40'
|
|
|
Specifications 40' x 20' x 5' Hydraulic Spud Barge Main Deck Plating = 5/16" Side Shell Plating = 5/16" Bottom Shell & Rake Bottom Plating = 5/16" Transom Plating = 5/16" 5x3x1/4” Angle Stiffeners on Hull Plates 5x3x1/4” Angle Stiffeners on Bulkheads One (1), 1/4" plate transverse bulkhead Two (2) coats anti-corrosive marine epoxy and one (1) coat of anti-fouling on the underwater hull. Outfitting: Two (2) 18” manholes Two (2) hydraulic spuds Proposed Scheduling Barge Delivery: Four (4) months after receiving first batch of material to the shipyard. We will do all we can to cut this time. Proposed Payment Schedule 30% due at contract signing. 30% due at erection of bulkheads, shell..
|
11. |
|
40' x 10' x 4' Spud Barges for Sale
|
|
2021
|
|
40'
|
|
|
Our new work barge features a raked bow, Heavy duty rub rails, Oversized large bitts and Centerline bulkheads. Pin 2 for 40x20 barges...easy to transport. 1/4 " plate construction & 10" spud collars / wells. Also can build 40X20 if a single barge is needed.
|
12. |
|
50' x 12' x 5' Sectional Barges On Order
|
|
2021
|
Sectional Spud Barge
|
50'
|
|
|
Barge Details – 2 - 12’x 50’x 5’ deep Also 12' x 57' x 4' Sectional Spud Barges Sectional Barges are raked 38 degrees one end with 12” channel head log Three (3) compartments each section three (3) flush mounted watertight hatches Four (4) 18” welded kevels on port and on starboard sides of the assembled platform • A36 1/4” plate throughout. All seams welded inside and out below the deck plate Two (2) bulkheads welded in barge, ¼” plate. Transverse frames on 24” centers: 3”x3”x1/4” angle Longitudinal angles under deck 3- 3”x3”x1/4” on 18” centers Connecting angles of 6”x4”x5/8&rd..
|